Path: utzoo!attcan!uunet!cs.utexas.edu!usc!apple!ames!pasteur!ucbvax!AERO4.LARC.NASA.GOV!blbates
From: blbates@AERO4.LARC.NASA.GOV ("Brent L. Bates TAD/TAB ms294 x42854")
Newsgroups: comp.sys.sgi
Subject: Re:  Advice needed interfacing a printer
Message-ID: <8907071551.AA07036@aero4.larc.nasa.gov>
Date: 7 Jul 89 12:51:29 GMT
Sender: daemon@ucbvax.BERKELEY.EDU
Organization: The Internet
Lines: 93


  I have used several printers on our 3130 with out too much problem.
(That is after I got everything working.)  I have conneted a HP ThinkJet,
a Seiko CH-5201 color hardcopy unit, a Tandy 24-pin dot matrix printer,
and a Tektronix 4693D printer to our 3130 through the serial ports
/dev/ttyf2 and /dev/ttyf3.  I had to use a serial to parallel converter
for the last three and some extra hardware to get the Seiko to work.
Follow the directions in section 7.9, pages 7-21 through 7-24 in the
IRIS Series 3000 Owner's Guide V3.0 or Appendix C, pages C-21 through
C-23 in the V2.0 Owner's Guide.  However, before doing so put the
appropriate filter into /usr/spool/lp/model.  Right now I use a Tektronix
4693D connected to the parallel port and two remote printers.
It has been long time since I used the serial ports for printers, I think
the interfaces still work.  I think one of the key things in getting the
interfaces to work was to use the timing functions of stty instead of null
character padding.
   I am enclosing the interfaces I used on these devices, I used the same
interface for the Thinkjet and Tandy printers:

-----------------------------Cut Here--------------------------------------

# lp interface for thinkjet printer
#
#       SCCS @(#)thinkjet   1.1
# @(#)$Header: /ws/2.0/2.0src/usr/src/usr.bin/lp/model/RCS/dumb,v 1.2 85/03/15 15:19:59 bob Exp $
# $Log: thinkjet,v $
# Revision 1.2  85/03/15  15:19:59  bob
# Revisized 8801.27 Brent L. Bates
# Added initial blank line (for csh) and what
# 

log=/usr/spool/lp/etc/log/thinkjet-log
seqid=$1
echo "Start $seqid - `date`" >> $log

stty 9600 ixon ixany ixoff -ofill cr0 nl0 tab0 bs0 ff1 vt0 0<&1
copies=$4
shift; shift; shift; shift; shift
files="$*"
i=1
while [ $i -le $copies ]
do
        for file in $files
        do
             cat "$file" 2>&1
             echo "\014"
        done
        i=`expr $i + 1`
done
echo "End $seqid - `date`" >> $log
exit 0
-----------------------------Cut Here--------------------------------------

# serial lp interface for seiko & Tektronix 4693D printers
#
#       SCCS @(#)thinkjet   1.1
# @(#)$Header: /ws/2.0/2.0src/usr/src/usr.bin/lp/model/RCS/dumb,v 1.2 85/03/15 15:19:59 bob Exp $
# $Log: thinkjet,v $
# Revision 1.2  85/03/15  15:19:59  bob
# Revisized 8807.01 Brent L. Bates
# Added initial blank line (for csh) and what
# 

log=/usr/spool/lp/etc/log/thinkjet-log
seqid=$1
echo "Start $seqid - `date`" >> $log

stty raw cs8 19200 -cstopb cread -clocal ixon ixany ixoff -ofill cr3 nl1 tab2 bs1 ff1 vt1 0<&1
copies=$4
shift; shift; shift; shift; shift
files="$*"
i=1
while [ $i -le $copies ]
do
        for file in $files
        do
           cat "$file" 2>&1
           echo "\0"
        done
        i=`expr $i + 1`
done
echo "End $seqid - `date`" >> $log
exit 0
-----------------------------Cut Here--------------------------------------
  I hope this helpful.
--

	Brent L. Bates
	NASA-Langley Research Center
	M.S. 294
	Hampton, Virginia  23665-5225
	(804) 864-2854
	E-mail: blbates@aero4.larc.nasa.gov or blbates@aero2.larc.nasa.gov