Path: utzoo!utgpu!jarvis.csri.toronto.edu!mailrus!tut.cis.ohio-state.edu!ucbvax!ULKYVX.BITNET!WSCART01 From: WSCART01@ULKYVX.BITNET Newsgroups: comp.sys.atari.st Subject: RE: Hard drive controler info... Message-ID: <8908041812.AA13908@jade.berkeley.edu> Date: 4 Aug 89 18:05:00 GMT Sender: daemon@ucbvax.BERKELEY.EDU Organization: University of Louisville Lines: 77 * Since I couldn't get my server to send this mail message * i'm left with no alternative but to post it to the net. * Sorry for any inconveience. * Stuart > From: harry@moncam.co.uk (Jangling Neck Nipper) > Subject:Where can I get: (a) 1.4 TOS (b) SCSI adaptor??? > Date: 31 Jul 89 18:57:26 GMT > Message-ID: > Are the TOS 1.4 ROM's available in the UK now, and if so, where? How > much? Can they be put into a (fairly ancient) 520? I have been told > no, but is this because 1.4 is going out on bigger ROM's, or will the > new TOS simply not work with such an old machine? I've no idea, but i dought it. > > Secondly, I have a Quantum 60 (100?) MB Hard Disk with embedded SCSI > that I want to use. I've heard that Adaptec make a controller to > go to SCSI; what's its number, and where (pref. UK) can I get it OK, here is the deal. You need a host adpater. Which is a DMA port to controler. I would recomend the ICD adapter. I just bought it and it seems to work well. (Problem is that it was version 2.7 and i know for a fact that software version 3.2 is out.) It was priced at $123 US. It is suppose to run with either a controler board (the adaptec you mentioned) or a embedded SCSI device (which you said it is). If you are in dought as to wither it is truely an embedded SCSI, check for the 50 pin plug. If it is there, the controler is built in, if not, you need a adaptec 4000a (repeat 4000a) controler for standard format. If your drive is RLL rated (an extended format) you need an RLL adaptec controler 4070. Finialy, if you cant get it to work, sell it to me for an absurdly low price. > (how much?). Also, the Supra HD software seems like a good thing > to get; again, where from and how much? ICD adapter comes with software. Total price should be $123 US. > > Thirdly, can I hang other devices off the SCSI? Someone said that you > could get more than one *hard* disk going because of the way the Supra > driver deals with them; would it handle other SCSI devices in the same > way, or would another driver be needed (assuming it's at all doable)? The ICD adapter can handle 7 devices. Device 6 is a built in clock. That leaves 6 drive spaces free. Also, you can buy controlers that control two drives for the price of one device. (You can have up to 12 hard drives.) > > Thanks in advance. You're welcome in advance... > -- > Harry Fearnhamm, EMAIL: harry@moncam.co.uk > Monotype ADG, ...!ukc!acorn!moncam!harry > Science Park, VOICE: +44 (0)223 420018 > Cambridge, FAX: +44 (0)223 420911 > CB4 4FQ, > ENGLAND. PS: I forgot to tell you, Tos 1.2 can only handle 16 megs at a time. You have to give you drive imaginary particions to access the full drive. EX: You have 50 megs, you make it think of 5 10 meg drives. (Tos 1.4 can handle 32 megs.) (It is covered in the ICD manual if you are confused.) Stuart (How's the weather up there? A nice hot 75F ? Snicker! :-) (I'm sitting here at 1 AM and it is 85 outside! Too hot for me!)