Path: utzoo!utgpu!news-server.csri.toronto.edu!bonnie.concordia.ca!thunder.mcrcim.mcgill.edu!snorkelwacker.mit.edu!usc!julius.cs.uiuc.edu!rpi!zaphod.mps.ohio-state.edu!samsung!rex!ukma!seismo!uunet!mcsun!ukc!newcastle.ac.uk!turing!ncrr
From: C.R.Ritson@newcastle.ac.uk (C.R. Ritson)
Newsgroups: comp.sys.encore
Subject: AnnexII, SL/IP & modems
Summary: Has anyone managed this
Message-ID: <1991Jan23.175944.17704@newcastle.ac.uk>
Date: 23 Jan 91 17:59:44 GMT
Sender: news@newcastle.ac.uk
Organization: University of Newcastle upon Tyne, UK, NE1 7RU
Lines: 101

I  hope  this  is the best newsgroup for this, as there is no xylogics
one.

I  have  been  trying to connect an annexII port up as a dial up SL/IP
link through a pair of modems to a single Apple  Mac.   I  have  found
that to make it work I had to switch off the modem control lines.  Has
anyone else done this?  If so, what annex configuration did you use?

Here is my annex configuration:-

set annex pref_load_addr 128.240.0.9
set annex pref_dump_addr 128.240.0.9
set annex image_name "oper.16.enet"
set annex subnet_mask 255.255.0.0
set annex broadcast_addr 0.0.0.0
set annex load_dump_gateway 0.0.0.0
set annex name_server_1 ien_116
set annex pref_name1_addr 128.240.0.9
set annex name_server_2 ien_116
set annex pref_name2_addr 128.240.0.5
set annex host_table_size 64
set annex pref_secure_host 0.0.0.0
set annex network_turnaround 2
set annex enable_security N
set annex load_dump_sequence net
set annex ipencap_type ethernet
set annex server_capability none
set annex syslog_mask emergency,alert
set annex syslog_facility log_local7
set annex syslog_host 128.240.0.9
set annex cli_prompt "annex: "
set annex timezone_minuteswest 0
set annex daylight_savings west_europe
set annex max_vcli 0
set annex rwhod Y
set annex min_unique_hostnames Y
set annex ring_priority 0
set annex routed Y
set annex motd_file "hoppen"

set port=17 speed 1200
set port=17 data_bits 8
set port=17 stop_bits 1
set port=17 parity none
set port=17 imask_7bits N
set port=17 control_lines none
set port=17 type dial_in
set port=17 mode slip
set port=17 forwarding_timer 0
set port=17 inactivity_timer 30
set port=17 port_multiplex N
set port=17 allow_broadcast Y
set port=17 max_session_count 3
set port=17 input_flow_control none
set port=17 input_start_char ^Q
set port=17 input_stop_char ^S
set port=17 output_flow_control none
set port=17 output_start_char ^Q
set port=17 output_stop_char ^S
set port=17 ixany_flow_control N
set port=17 long_break Y
set port=17 short_break Y
set port=17 attn_char ^@
set port=17 user_name ""
set port=17 prompt "annex: "
set port=17 term_var "slip"
set port=17 input_buffer_size 4
set port=17 bidirectional_modem N
set port=17 default_modem_hangup N
set port=17 location "B340"
set port=17 input_is_activity Y
set port=17 output_is_activity Y
set port=17 reset_idle_time_on input
set port=17 cli_security N
set port=17 connect_security N
set port=17 port_server_security N
set port=17 dedicated_address 0.0.0.0
set port=17 dedicated_port telnet
set port=17 newline_terminal N
set port=17 leap_protocol_on N
set port=17 echo Y
set port=17 map_to_lower N
set port=17 map_to_upper N
set port=17 char_erase Y
set port=17 line_erase Y
set port=17 hardware_tabs N
set port=17 erase_char ^?
set port=17 erase_word ^W
set port=17 erase_line ^U
set port=17 redisplay_line ^R
set port=17 toggle_output ^O
set port=17 telnet_escape ^]
set port=17 slip_local_address 128.240.1.11
set port=17 slip_remote_address 44.131.18.17
set port=17 slip_subnet_mask 255.0.0.0
set port=17 slip_load_dump_host 0.0.0.0
set port=17 slip_metric 1
set port=17 slip_allow_dump N
set port=17 cli_inactivity immediate

Chris Ritson <C.R.Ritson@newcastle.ac.uk>