Relay-Version: version B 2.10 5/3/83; site utzoo.UUCP
Path: utzoo!watmath!clyde!burl!ulysses!allegra!princeton!orsvax1!pyrnj!caip!lll-crg!lll-lcc!langdon
From: langdon@lll-lcc.UUcp (Bruce Langdon)
Newsgroups: net.micro.atari8
Subject: Re: ACTION! plea, once again
Message-ID: <201@lll-lcc.UUcp>
Date: Fri, 21-Mar-86 14:39:04 EST
Article-I.D.: lll-lcc.201
Posted: Fri Mar 21 14:39:04 1986
Date-Received: Sat, 22-Mar-86 23:22:43 EST
References: <8603101331.AA19883@mitre.ARPA>
Organization: Lawrence Livermore Labs, LCC, Livermore Ca
Lines: 69
Summary: CHAIN.ACT, from OSS

In article <8603101331.AA19883@mitre.ARPA>, ajb@MITRE.ARPA (Alan Broder) writes:

> I need to know several things about advanced programming in ACTION! :
>  
> 	1) Is it possible to "chain" ACTION! programs (load in and
> 	   execute a new program at termination of first program).

The following is from the OSS bulletin board, (408) 446-3451.
It may require use of their DOS XL. I haven't tried it.

----------------------------------------------------------------------
	Bruce Langdon  L-472                langdon%lll-lcc@lll-crg.ARPA
	Physics Department                  "langdon#bruce%d"@lll-mfe.ARPA
	Lawrence Livermore National Laboratory       
	Livermore, CA 94550                 (415) 422-5444
UUCP: ..{gymble,ihnp4,seismo}!lll-crg!lll-lcc!langdon
----------------------------------------------------------------------
; Chain - ACTION! program loader
;   by Mark Rose - February, 1985

PROC LoadFile=*( BYTE x )
    CARD goAddr    = $2E2,
         startAddr = $6F0,
         endAddr   = $6F2
    BYTE rtn       = $6F4

  [
    $0A $0A $0A $0A $AA $A9 $60 $8D
    rtn $A9 $80 $8D goAddr $A9 $06
    $8D goAddr+1 $A9 $F0 $A0 4 $9D
    $344 $A9 $06 $9D $345 $98 $9D
    $348 $A9 0 $9D $349 $A9 7 $9D
    $342 $20 $E456 $10 3 $6C goAddr
    $AD startAddr $C9 $FF $D0 23 $4D
    startAddr+1 $D0 18 $AD endAddr
    $8D startAddr $AD endAddr+1 $8D
    startAddr+1 $A9 $F2 $A0 2 $D0 $C4
    $AD endAddr $38 $ED startAddr $9D
    $348 $AD endAddr+1 $ED startAddr+1
    $9D $349 $FE $348 $D0 3 $FE $349
    $AD startAddr $9D $344 $AD
    startAddr+1 $9D $345 $A9 7 $9D
    $342 $20 $E456 $10 $8F $98
    $4C Error
  ]
PROC LoadEnd=*()



PROC Chain( BYTE ARRAY fileName )
    Close( 1 )
    Open( 1, fileName, 4, 0 )
    MoveBlock( $600, LoadFile, LoadEnd-LoadFile )
    LoadFile( 1 )
RETURN

; From your ACTION! program, call the
; procedure Chain with the name of
; the ACTION! program to which you
; want to chain as the parameter.
; For example,
;    Chain( "D:NEXTPROG.COM" )
; would cause "NEXTPROG.COM" to be
; run as a binary file.  The desired
; file MUST have been written to disk
; using the "W" command from the
; ACTION! monitor.

MODULE