Relay-Version: version B 2.10 5/3/83; site utzoo.UUCP
Path: utzoo!mnetor!seismo!lll-crg!mordor!sri-spam!sri-unix!hplabs!nsc!voder!kontron!stephan
From: stephan@kontron.UUCP (Stephan W. Wendl)
Newsgroups: comp.sys.m68k
Subject: (Re: Re: Single board computer) available
Message-ID: <1187@kontron.UUCP>
Date: Tue, 11-Nov-86 13:44:33 EST
Article-I.D.: kontron.1187
Posted: Tue Nov 11 13:44:33 1986
Date-Received: Wed, 12-Nov-86 02:11:37 EST
References: <52@cogent.UUCP>
Organization: Kontron Electronics, Mt. View, CA
Lines: 84

> 
> In article <3601@utcsri.UUCP> drg@utcsri.UUCP (Dave Galloway) writes:
>>The EE department here has been using a 6809 based single board computer
>>
>>They would like to replace this board with something more modern. 
>>	a) 16 bit CPU
>>	b) MMU
>>	c) .5 - 2 Meg RAM
>>	d) EPROM
>>	e) 4 serial ports
>>	f) 2 parallel ports
>>	g) Ethernet interface
>>	h) some sort of bus connector to teach simple interface design
>>
>>Does anyone know of an existing board that comes close to those requirements ?
> 
> Please let me know also about such a beast.  I want a 16 bit system on a 
> single board for personal use, preferably in kit form to reduce cost.  I can
> do without the Ethernet and the many ports, I would mainly need one or two
> serial ports and a decent bus that I could map low level IO devices of my
> own into.  And a decent monitor, of course.
> 

Two 68000 Multibus systems for sale :
Each system comes with the following parts

	1. one 68000 CPU board with
		8Mhz CPU
		memory management similar to SUN 1 Board
		two serial ports
		timer
		64 Kbyte of Prom (boot prom)
		
	2. one serial card with
		4 serial ports RS232 one DMA/sio (multiplexed)
		2 serial ports RS422 one DMA/direction/sio
	
	3. one controller board with
		sasi hard disk controller DMA controlled
		8" Floppy controller (IBM format double sided, double density)
		printer port (parallel)

	4. two memory boards
		512 Kbytes each with ECC controlled memory (3bits for recovery)
	
	5. one 8" double sided floppy drive (half height)
	
	6. one 5Mbyte hard disk (to fill the space)
	
	7. one multibus cabinett with
		7 multibus slots
		1 power supply (switched)
		2 fans
		  cabeling for 8 serial boards and ethernet (includes cable)
		  		centronics printer connector
		space for two harddisks (vertically mounted)
		
		Size (not exact):  10" x 17" x 21"
			
	8. schematics, boot prom listing and some format utilities in
	   source and binary. (programs in listing and machine readable form)
	   
	   The boot prom support boots from hard disk, floppy disk and via serial
	   line. S-records can be loaded via serial line. Included are also complete
	   hardware diagnostic routines.
	   Configuration via switches for direct boot sequence or monitor after power
	   up. Device driver in boot prom. Further commands to examine and set memory.  
	   	   
	   
	Asking $1000 each. Discount 10% if you purchase both. Prefer if you
	pick it up but can be shipped within USA (I would take it apart for
	easier shipping and protection of the parts. It's easy to assemble)
	
	If there are any question of technical kind feel free to ask.
	
	Please reply via e-mail or call me:
	
			Stephan W. Wendl
			private (415)-3 255 377 after 7pm or leave message
						I call back
						
			work    (415)-965-7020 x136 
				  ^ this is ~ 35 miles south of San Francisco
				    in Palo Alto/Mountain View