Path: utzoo!mnetor!uunet!husc6!think!ames!ucbcad!ucbvax!WALKER-EMH.ARPA!hicks From: hicks@WALKER-EMH.ARPA (Gregory Hicks COMFLEACTS) Newsgroups: comp.sys.ibm.pc.digest Subject: Info-IBMPC Digest V6 #74 Message-ID: <8712281415.AA01156@ucbvax.Berkeley.EDU> Date: 28 Dec 87 11:40:40 GMT Sender: daemon@ucbvax.BERKELEY.EDU Organization: The ARPA Internet Lines: 549 Approved: info-ibmpc@b.isi.edu Info-IBMPC Digest Wed, 23 December 1987 Volume 6 : Issue 74 This Week's Editor: Gregory Hicks -- Chinhae Korea Today's Topics: Alternate Networks Microsoft C compiler setup program Software to Transfer Binary Files from SIMTEL20 to VAX/VMS hosts and in KB.ASM Xmodem for 4.2/4.3 BSD Unix (and maybe Sys V) Software available from SIMTEL20 MIDI for the IBMPC Satellite Tracking Software Summary Lab Tech Notebook and Dadisp (2 msgs) Mouse Message Decoding Today's Queries: Printing of Music Script BBS for IBM or clone using MSDOS Problems with hard-disk MS-C 5.0 and -386 Support Software Vandalism VT240 Emulator for PC Request Help on disk drives & monitors Disabling XT Keyboard Typematic PCChart vs Graftalk Problems with Sidekick and DOS 2.11 backup 3-dimensional Graphics Program Needed AUTOMENU - help please Driver for Summagraphics Graphics Tablet needed INFO-IBMPC BBS Phone Numbers: (213)827-2635 (213)827-2515 ---------------------------------------------------------------------- Date: Fri, 25 Dec 87 11:00 GMT From Gregory Hicks COMFLEACT Subj: Alternate Networks In Issue #73, I made an addendum to the request from Thomas Lapp on information about alternate networks and how to join. I mentioned the October 87 issue of the Proceedings of the ACM. I made a mistake: It should have been the October 86 issue from the Communications of the ACM. The article is titled "Notable Computer Networks". Regret the error. Gregory Hicks ------------------------------ Date: Thu, 19 Nov 87 18:44:33 EST From: Joe Morris (jcmorris@mitre.arpa) Subject: Microsoft C compiler setup program For anyone getting the Microsoft C Compiler Release 5.0: somebody at Microsoft apparently changed the setup program after the beta tests were finished, causing it to attempt to write on the last distribution diskette instead of the hard disk during installation. Microsoft says that this shouldn't cause any problems, but can't say why the program is doing this. They insist that "it didn't do that in the internal tests". I replied "ignore" to the error message when it tried to write through my file protect tab, and the installation seems to have run to completion without any errors. A little experimentation showed that it is apparently writing temporary files with data from the SETUP command line, then erasing the file. Joe Morris ------------------------------ Date: Fri, 4 Dec 1987 14:39 MST From: "Keith Peterson" W8SDZ @ SIMTEL20.ARPA Subject: Software to Transfer Binary Files from SIMTEL20 to VAX/VMS hosts The program below may help solve the problem of transferring binary files from SIMTEL20 to VAX/VMS hosts. Filename Type Bytes CRC Directory PD1: BINTNXVMS.C.1 ASCII 10823 23F1H BINTNXVMS.README.1 ASCII 336 1D2EH Here is the readme file: BINTNXVMS.C is for use on VAX/VMS systems to convert a TOPS-20 file transferred in FTP "binary" mode to "tenex" mode. In "binary" mode, we have 2 36-bit words in 9 8-bit bytes. In "tenex" mode, we want the top 32 bits of each 36-bit group, giving 8 8-bit bytes. See the notes in BINTNXVMS.C for instructions on command options. --Keith ------------------------------ Date: Mon 14 Dec 87 19:46:28-PST From: KNIGHT @ Russell.Stanford.EDU Subject: and in KB.ASM Using KBEDIT.ASM, a public domain command line editor/expanded typeahead buffer/command history hack, I have made KB.ASM, which provides ^W and ^U command line editing, as well as other useful changes. KB.ASM is available via anonymous FTP from SIMTEL20.ARPA. File infor- mation follows: Filename Type Bytes CRC Directory PD1: KB.ASM.1 ASCII 77846 FFC4H Instructions for building the device driver are contained in the file. Bob ------------------------------ Date: Sun, 6 Dec 1987 10:25 MST From: W8SDZ @ SIMTEL20.ARPA Subject: Xmodem for 4.2/4.3 BSD Unix (and maybe Sys V) Filename Type Bytes CRC Directory PD2: XMODEM34.SHAR.1 ASCII 84452 D010H The xmodem program implements the Christensen (XMODEM) file transfer protocol for moving files between 4.2/4.3BSD Unix systems and microcom- puters. The XMODEM/CRC protocol, the MODEM7 batch protocol, the XMODEM-1K block protocol and the YMODEM batch protocol are all supported by xmodem. For details of the protocols, see the document edited by Chuck Forsberg titled XMODEM/YMODEM Protocol Reference. This program runs on 4.2/4.3BSD systems ONLY. It has been tested on VAXes and Suns against the MEX-PC program from Niteowl Software and the ZCOMM and DSZ programs from Omen Technology. ------------------------------ Date: Thu, 10 Dec 1987 20:32 MST From: W8SDZ @ SIMTEL20.ARPA Subject: Software available from SIMTEL20 The long-awaited PIBterm 4.0 modem terminal and file transfer program for MSDOS is now available from SIMTEL20, complete with source code... Filename Type Bytes CRC Directory PD1: PIBT40S1.ARC.1 BINARY 215021 7383H \ PIBT40S2.ARC.1 BINARY 228059 6782H \ PIBT40S3.ARC.1 BINARY 218541 BB6CH /- source PIBT40S4.ARC.1 BINARY 239802 5FFEH / PIBT4EXE.ARC.1 BINARY 349304 D5F5H PT4DOCS.ARC.1 BINARY 226867 75C9H PT4FNOTE.DOC.1 ASCII 541 4B94H PT4SREAD.ME.1 ASCII 12677 DFC6H --Keith Petersen Arpa: W8SDZ@SIMTEL20.ARPA Uucp: {bellcore,decwrl,harvard,lll-crg,ucbvax,uw- beaver}!simtel20.arpa!w8sdz ------------------------------ Date: Sun, 13 Dec 87 16:23:42 PST From: Dallas_Hinton%UBC.MAILNET@um.cc.umich.edu Subject: MIDI for the IBMPC The synthesizer board which IBM is selling is functionally identical to a Yamaha multi-timbral box. It contains several (8?) synthesizers with no keyboard, plus a drum machine. It is quite a good sound (in fact one of the best sounding units I've heard) but is somewhat clumsy to work with. A cheaper route, but equally satisfactory, is the Roland MT-32 which is 8 single-voice synths plus drum machine, again with no keyboard. Both the MT-32 and the Yamaha equivalent (whatever it's number is) are in the 700 to 1000 Canadian price range. I can't truthfully see any point in wasting a slot on an internal sys- tem unless you're on the road a LOT and need the space. I think you'll find an external system more flexible and more friendly. Try an MT-32 or equiv. box with a Roland S-10 sampling keyboard. It will cost about the same and do wonderful things! Cheers, Dallas Just for information, I am a music teacher at a secondary school in Vancouver, B.C., and have no connection with any commerical (or non- commercial) company of any sort. I have been using MIDI based equipment in the classroom for about 2 1/2 years now, and am still learning. I will be the first to admit that I am biased...I believe in using what works, regardless of who makes it! ------------------------------ Date: Wed, 9 Dec 87 11:22:51 MST From: John Shaver Modernization Office Subject: Satellite Tracking Software Summary From: <11SSTEIN%GALLUA.BITNET@WISCVM.WISC.EDU> I would suggest that you ask this user for the program... DWELLS@NRAO.BITNET - National Radio Astronomy Observatory... 11SSTEIN@GALLUA From: bobw%chem.span@VLSI.JPL.NASA.GOV (Bob Wood WA7MXZ, USU Chemistry) The best satellite tracking program I have ever seen for PC use was written by Dr. Bob McGwier, N4HY. His program is available from: AMSAT (Amateur Satellite Corp.) P.O. Box 27 Washington, D.C. 20044 (301)589-6062 The price is very nominal. The program can run with an 8087 coprocessor to speed up calculations. The graphics are very good, the system is easy to use and can be interfaced to an antenna tracking system. Bob Wood, WA7MXZ From: Dallas_Hinton%UBC.MAILNET@um.cc.umich.edu Almost any decent Amateur Radio shop should produce several pieces of software for tracking satellites in both real and step time. Most if not all require an 8087 math co-processor (or equiv.). From: allegra!ulysses!sfmag!sfsup!sfmin!martyf@EDDIE.MIT.EDU Enclosed is a basic program that calculates the azimuth and elevation for satelite tracking systems. The source of this program is unknown, however it appears to do the job. Marty Fleming attunix!martyf 201 522 5001 [SATELITE.BAS has been added to the Info-IBMPC Lending Library. --gph] ------------------------------ Date: 2 Nov 87 14:34:41 PST (Monday) From: Bicer.ES@Xerox.COM Subject: Lab Tech Notebook and Dadisp Has anyone heard of programs called "Lab Tech Notebook" and "Dadisp"? Does anyone know where or how to get them? Thanks in advance, Jack Bicer Bicer.ES@Xerox.COM ------------------------------ Date: Mon, 02 Nov 87 17:36:40 -0800 From: Roy Stehle Subject: Lab Tech Notebook and Dadisp The following is taken from a catalog of Interleave, Inc., 2940 Noble Road #3, Cleveland Heights, Ohio 44121. (216) 291-1001. Order No. 4017A DADISP by DSP Systems, $795.00 Order No. 8002A Labtech Notebook by Laboratory Techniques, $895.00 I have not done business with this company and I would expect other suppliers could meet your needs. Roy Stehle SRI International ------------------------------ Date: Thu, 5 Nov 87 13:18:36 EST From: jcm@ORNL-MSR.ARPA (James A. Mullens) Subject: Mouse Message Decoding The PC Mouse people (Mouse Systems) originally made a mouse that took its power from a AC-DC transformer which you plugged into the wall. If you have trouble supplying power via the 232 port, you might try to find the older model (and save some money too). The PC mouse documentation does explain how to decode the mouse mes- sages. They offer to send the source code to their installation test program. It is very easy to decode the mouse messages. I can't tell you how much power the new PC Mice use from the serial port (I have the old model). ------------------------------ Date: Thu, 05 Nov 87 16:07:34 SST From: "L. Chandra" Subject: Printing of Music Script I am looking for software to print professional quality Music Script. I know of SongWrite (ver I) but it is not good enough. I would appreciate any recommendations. Thank you. ------------------------------ Date: Fri, 6 Nov 87 14:46 EST From: Subject: BBS for IBM or clone using MSDOS I need a bulletin board system to run on MSDOS and a PC or clone. Preferably it would be public domain, but if anyone knows of a good shareware BBS, i'd be interested in it also. Thanks, Bruce Harrison Univ. of Tenn. at Martin BRUCEH@UTKVX1 (bitnet) ------------------------------ Date: Tue, 15 Dec 87 11:36:54 SST From: RPR9385%NUSVM.bitnet@cunyvm.cuny.edu Subject: Problems with hard-disk I have a cheap IBM PC clone, running at 4.77/8 MHz with DOS 3.1. Recently I bought a hard-disk (SEAGATE ST 238 30Mb) to use with my PC. However, my system refuses to work with my hard-disk at 8 MHz. If I switch my PC to 8 MHz, it will run fine for 10-15 minutes and then the PC freezes up and only a CTRL-ALT-DEL will work. There is not problem when running at 4.77 MHz. But I long for the 8 MHz speed. I don't know much about the inner workings of the PC, so I am unable to solve this problem. I wonder if anyone out there might have any suggestions for me. Thanks! ------------------------------ Date: Thu, 10 Dec 87 17:22:15 est From: stev@OBERON.LCS.MIT.EDU (Stev Knowles) Subject: MS-C 5.0 and -386 Support We just got in our copies for MSC5.0 and it doesnt seem to support 80386 code. (*sigh*). is there a free update on the way? well, any recommendations about good 386 compilers? any word from Microsoft about when to expect support from them? thanx . . . stev knowles ftp software 617-868-4878 ------------------------------ Date: 08 DEC 87 09:00 EST From: V2002A%TEMPLEVM.BITNET@CUNYVM.CUNY.EDU Subject: Software Vandalism Are there any legal precedents on the books for software vandals caught willfully propagating 'virus' or 'infectious' programs? I ask this because I received the following on another network. Andy Wing V2002A%TEMPLEVM.BITNET@CUNYVM.CUNY.EDU From: Kenneth R. van Wyk, User Services Senior Consultant, Lehigh Univ. Last week, some of our student consultants discovered a virus program that's been spreading rapidly throughout Lehigh University. We have no idea where the virus started, but some users have told me that other universities have recently had similar problems. The virus: the virus itself is contained in the stack space of COMMAND.COM. When a pc is booted from an infected disk, all a user need do to spread the virus is to access another disk via TYPE, COPY, DIR, etc. If the other disk contains COMMAND.COM, the virus code is copied to the other disk. A counter is incremented on the parent. When this counter reaches a value of 4, any and every disk in the PC is erased thoroughly. The boot tracks are wiped, as are the FAT tables, etc. This affects both floppy and hard disks. Meanwhile, the four children that were created go on to tell four friends, and then they tell four friends, and so on. Detection: First, the write date of the command.com changes. Second, if there's a write protect tab on an uninfected disk, you will get a WRITE PROTECT ERROR... So, boot up from a suspected virus'd disk and access a write protected disk - if an error comes up, then you're sure. Note that the length of command.com does not get altered. I urge anyone who comes in contact with publicly accessible disks to periodically check their own disks. Also, exercise safe computing - always wear a write protect tab. ------------------------------ Date: 08 Dec 87 09:30 EDT From: C0144%CSUOHIO.BITNET@WISCVM.WISC.EDU Subject: VT240 Emulator for PC Request Can anyone supply me with a public-domain VT-240 terminal emulator for a PC/XT/AT? There are several people here at Cleveland State that would like to make use of it if I can find one. Thanks. -Dave Chatfield C0144%CSUOHIO.BITNET@WISCVM.WISC.EDU ('til 12/15/87) necntc!ncoast!ohiont!davec@husc6.harvard.edu ------------------------------ Date: Tue, 08 Dec 87 13:40:14 CST From: Derek Morgan Subject: Help on disk drives & monitors Does anybody out there know of any monitor/video card sensing and set- ting software? Also, any ideas on how to sense a disk drive type would also be appreciated. We have a variety of monitors and disk drives to cope with when writing applications in C (Microsoft 5.0). It'd be nice to be able to define monitor and disk drive configuration at run-time instead of compiling one version for every combination, or am I just dreaming? Thanks in advance, Derek Morgan Disclaimer: Personal opinions in this posting. Washington University Medical Comp. Services ------------------------------ Date: Thu, 10-DEC-1987 17:00:22.41 GMT+1 From: Subject: Disabling XT Keyboard Typematic Does somebody know how I can switch off the Typematic action of the XT- Keyboard. Yes.. I know how to find out whether a scan code comes from a key that was pressed several times or from Typematic, but I have an application where for a key I only get the press and release code be it pressed 1 mil- lisecond or 1 year. Dieter Menne Biologie III - Zoophysiologie 7400 Tuebingen F.R. Germany Bitnet BPme001@DTUZDV5A ------------------------------ Date: Thu, 10 Dec 87 13:57:27 EST From: gorman@braggvax.arpa Subject: PCChart vs Graftalk I am trying to provide a colleague with unbiased comparitive evalua- tions of GrafTalk (Version 4) and a lesser-known business graphics package, PCChart by Aztec, and would like any comments, favorable or unfavorable, as to eithers user interface, ease of application, performance, local area network support, and general utility. Thanks in advance, Bryan L. Gorman ------------------------------ Date: 8 December 1987, 09:48:41 MEZ From: "Rainer Kleinrensing" UNI217%DBNRHRZ1.BITNET@CUNYVM.CUNY.EDU Subject: Problems with Sidekick and DOS 2.11 backup We currently have a problem with Sidekick V1.50: we are using a COMPAQ portable (COMPAQ Plus, PC-compatible) with a NEC V20 and DOS 2.11. Due to the special application software we cannot switch to DOS 3.x (the software will hang). The problem: when Sidekick is in memory and we make a backup using the standard DOS Backup program, all works. However, when trying to restore the backup, RESTORE says the files on the disk are in the wrong order and stops. When we remove Sidekick from memory, the backup/restore sequence works fine. Has anybody out there had any (perhaps different) problems with Sidekick or the backup program? Thank you, Rainer Kleinrensing ------------------------------ Date: Mon, 14 Dec 87 10:03:19 +0200 From: Subject: 3-dimensional Graphics Program Needed My research on dynamic systems encountered in game theory have lead me to the following problem: I have to view the graph of a function z=f(x,y), say from a position in the first orthant above the surface of the graph. Moreover, I want to see a path on this surface, given by a sequence (x(n),y(n)), n=1,2,3,... The function f(x,y) is essentially arbitrary (I have to study several such examples). For a different project, I would also like to see a trajectory under the graph leading from the origin to a point on the surface. The trajec- tory is given by a sequence (x(n),y(n),z(n)), n=1,2,... Does any one know or have a program that could help me? Can any one suggest where to find formulas that could plot points (x,y,z) in a way that gives impression of a 3-dimensional object, so that I can program my own routines for these programs? Please send a reply directly to MASCHLA@HBUNOS.BITNET. I shall post any useful answer that I get to info-ibmpc. Thank in advance, Michael Maschler Department of Mathematics The Hebrew University, Jerusalem ------------------------------ Date: 14 Dec 87 10:31:12 GMT From: trw@hrc63.co.uk (Trevor Wright Marconi Baddow) Subject: AUTOMENU - help please I have seen a small utility called AUTOMENU and obtained an evaluation copy. It seems to be public domain or shareware. Can anyone please confirm this and if possible provide a list of the characters that drive the definition of menus in the data files. If anyone can give me the author and cost then so much the better - is there a UK distributor. ------------------------------ Date: Fri, 11 Dec 87 17:34:55 EST From: gorman@braggvax.arpa Subject: Driver for Summagraphics Graphics Tablet needed Anyone out there with an MS-DOS driver for a Summagraphics MM 12X12 graphics tablet? Please reply directly. Thanks. Regards, Bryan Gorman gorman@braggvax.arpa ------------------------------ ************************ End of Info-IBMPC Digest -------