Path: utzoo!attcan!uunet!lll-winken!xanth!mcnc!thorin!clocs!davis From: davis@clocs.cs.unc.edu (Mark Davis) Newsgroups: comp.sys.ibm.pc Subject: Re: Hard Drive Characteristics Summary: Lots of Places and it depends Keywords: heads, cylinders, FAT, llformat, format, partition, etc Message-ID: <7313@thorin.cs.unc.edu> Date: 19 Mar 89 04:39:31 GMT References: <2369@lll-lcc.UUCP> Sender: news@thorin.cs.unc.edu Reply-To: davis@cs.unc.edu (Mark Davis) Organization: University Of North Carolina, Chapel Hill Lines: 109 In article <2369@lll-lcc.UUCP> rzh@lll-lcc.UUCP (Roger Hanscom) writes: >Does anybody know where a hard drive's parameters are known (or >determined) ?? ... Lots of places. It depends on ... DOS seems to get the geomtry, like number of heads from the BIOS, which may get it from CMOS drive type, or from the disk itself or ROM, but the size of the disk (even logical disks) from the partition table recorded on the first physical sector on the disk. > ... You do a low-level format of the drive by entering >firmware on the controller card....does the controller have some >sort of an internal table that gives these parameters. ... Sometimes ... It depends on the controller. I have a WD 27X controller that gets the parameters for drive 0 from ROM (as controlled by a strap), but for drive 1, it always asks for the drive geometry. The Premier 1000 that I work with came supplied with a WDFMT program that always asks for all of the geometry although I have other programs that are smart enough to ask the same hardware. AT's and compatibles save the drive type number in the memory on the clock chip: a type 44 drive is an ST 251, a type 35 is an ST 4096, a type 32 is an ST 4053, etc. After boot, these computers reference the CMOS and then the ROM to give the BIOS the proper drive geometry. Some controllers actually record the drive information on the drive in proprietary format. This is also the popular method amoung third party drivers. > ... When you >run FORMAT, how does it know (for example) how many heads are in >the hard drive?? ... It gets the information from DOS (unlike FDISK, which gets the information from BIOS). > ... Is any of this controlled by the BIOS?? ... It is mostly controlled by bios or indirectly by DOS. Logical drives are handled by DOS, and you can control some things through DOS. For example, when I put an ST 4096 on a PS/2, I had to talk to the BIOS (int 13, 0Dh reset hard disk) to get FDISK to work properly, but I had to use DOS (int 21h, func 44h, sub func 0Dh) to get FORMAT to work properly. Be careful about saying BIOS. Some of the BIOS is in ROM, some of it is on disk with the rest of the operationg system. > ... Why does >DOS refuse to deal with FORMAT C:/N:xx , where xx is less than the >drive's xx-max?? ... My PC-DOS manual says that /n and /t are only applicable to floppy's. > ... Is the set of hard drives a controller will work >with closed?? (By that I mean will a controller that was built >when there were no 13-head drives with 2000 cylinders be able to >handle a drive with these characteristics?? ... Controllers of various types seem to be limited to: a. 20 Megabytes (very old, may be myth) b. 8 heads (somewhat old) c. 1024 cylinders (also somewhat old) I don't know specific controller combinations except the only 20 meg limit was very old IBM controllers. Of course, there are always SCSI and ESDI controllers and drives, but ... In general, reasably modern (after 1982) controllers are not too limited, but be careful of the above limits. > ... Or is the limitation >more a function of raw number of sectors on the entire device??) The controller limitations are considerably muddied by the fact that DOS has: a. 1024 cylinder limit (somewhat corrected by third party drivers) b. one DOS 32 Meg partion per physical device (until 3.3) c. 32 Meg limit from 16 bit sector count (overcome by 4.0 or Compac 3.3+) All of the above DOS limits can be overcome by appropriate 3rd party drivers (like Disk manager or Speedstor). Be careful, though, for example, a sales person from Ontrack told me that they had not mastered greater than 1024 cylinders on PS/2's. Also, there seems to be a 64 Meg file size limit that is not helped by the third party software. >One frequently encounters comments about the "32 MByte" limit -- >what dictates this "limit" (is it as I suspect, the size and # of >bits per entry in the FAT) ?? Until DOS 4.0 (or COMPAC 3.3+ or other drivers), this was a "logical disk" limit, but you could have 4 logical disks on a physical disk. I have a 32, 32, and 16 Meg partitions on a PC/DOS 3.3 80 Meg disk. 32 meg comes from 16 bits (64 K) times .5 meg (512 byte) sectors to give the number of logical sectors on a disk. In fact with 16 bit (64K) * clusters of 2K each could handle 128Meg. (12 bit fats (4 Meg) * with 4K clusters handles 16 Meg disks.) OK. Now for the summary. If you have a relatively recent controller, you can do much of what you ask. But you may need software. All Seagate drives come with Disk Manager 3.5, which will do fine for AT's and XT's and compatibles. Other vendors do similar things. A couple of mail order vendors ship Speedstor with every Maxtor Drive. If you really want a big drive, call somebody with your specifics, and make sure the drive they ship you will work with your system. If you want more specifics, either tell us the hardware combination that you are working from (type of computer, type of controller and DOS version), and what you want to add. Or you could buy a good DOS book. Hope this helps - Mark (davis@cs.unc.edu or uunet!mcnc!davis)