Path: utzoo!attcan!utgpu!jarvis.csri.toronto.edu!clyde.concordia.ca!uunet!cs.utexas.edu!rutgers!cbmvax!daveh From: daveh@cbmvax.commodore.com (Dave Haynie) Newsgroups: comp.sys.amiga Subject: Re: Help! A2630 hates my 2000 Message-ID: <9028@cbmvax.commodore.com> Date: 15 Dec 89 12:13:46 GMT References: <111400068@uxa.cso.uiuc.edu> Organization: Commodore, West Chester, PA Lines: 69 in article <111400068@uxa.cso.uiuc.edu>, bty00298@uxa.cso.uiuc.edu says: > Nf-ID: #N:uxa.cso.uiuc.edu:111400068:000:1848 > Nf-From: uxa.cso.uiuc.edu!bty00298 Dec 10 00:17:00 1989 > I just got my A2630 as of December 8 (Friday) and all is not well. After > many problems with random GURU's, trying every configuration possible, > replacing all of the chips on the motherboard, the silly thing finally > worked with all the boards in another Amiga. What gives? The only difference > between the two motherboards is that I have a 4.1 and we put it into a 4.2. It sure couldn't hurt to have your motherboard brought up to Rev 4.5 status, or thereabouts, if you really have a 4.1 or 4.2 motherboard (check the paper sticker, not the PCB artwork). But there's nothing other than the extra pullup on BAS* (1k between pins 20 and 11 on U605) that's an obvious difference. > Well we thought everything had been solved - probably a defective motherboard > or at least a picky one - but no. Now it appears that sometimes on powerup > the unit locks up on the white screen. When this is occurring, a warm reboot > and a double mouse press later into 68000 mode, the unit goes into a > constant black-grey-black screen cycle. I'm not sure I know what's you're saying here. Of course, I've been up all night, it might make more sense after a few hours sleep. BUT in any case, a lockup on a cold start definitely sounds like some flakiness. Switching into 68000 mode on a warm start can definitely cause problems, though. Exec isn't really graceful yet about switching CPU types, so if you boot up in 68030 mode, then reset back to the 68000, Exec may very well warm boot assuming you have a 68030, and get real confused. A minute or two of power down (whatever these DRAM need lately) and a cold boot into 68000 mode should always work. > Another more frequent but less urgent problem has to do with the 2088 bridge- > board. Sometimes Janus recognizes its presence and at other times it ignores > it. This is usually remedied by restarting from a cold boot, but this is > complicated by the above. The binddrivers appears successful because the PC > side boots, but the Amiga side just complains that Janus.library is not > available. This is apparently a known problem with the current janus software. The software is kicking in before the PC has it's refresh turned on, and this is considered an error, so janus kicks itself out of memory. It looks like the board never gets configured, but if you list your configured devices, you'll see it's there. While the problem is aggrevated by a fast Amiga, it's possible for this to happen on any Amiga. > Please can someone help! Hopefully someone at Commodore such as Dave Haynie > can give some advice. > Micron 2MB card > MicroBotics HardFrame w/Quantum 40S Do the symptoms change with either or both of these removed. If you have a very old HardFrame, you may need an update to it -- there was a minor bug in the early ones that caused problems with A2620 and probably A2630 (it was fixed before we put together an A2630 and HardFrame in the same machine; today, they work fine together). > Any help or comments will be appreciated! Did the setup work properly in the other 2000, or was it still flakey? While it would be rather astonishing, it's always possible there's a problem with the A2630; verifying that independently of your A2000 is a good idea. If you can send me any more details I might be able to think of something. After I catch some ZZzzzzzs.... > Brian Yamanaka -- Dave Haynie Commodore-Amiga (Systems Engineering) "The Crew That Never Rests" {uunet|pyramid|rutgers}!cbmvax!daveh PLINK: hazy BIX: hazy Too much of everything is just enough